Page path:

Equipment for hire

You can make Xpedeo loan devices available to your visitors if they have not brought their own smartphones with them, or if they are unable or unwilling to use them.

We also provide suitable charging stations for the devices, into which they can be easily plugged in and unplugged.

xpedeo-Leihgerät im Einsatz

Issuing of equipment

Select a device with a high battery charge. The battery charge is high if you see a green number, or if the screen is completely black (when fully charged, the devices go into standby mode).

Remove the Guide from the charging station. After a few seconds, the screen will change and the xpedeoscreen will be displayed (xpedeo logo and arrow). In this mode, the device will return to standby after one minute. To switch it back on, press the side of the casing once or briefly place it back in the charging station.

Tap the arrow once on the xpedeoscreen: the start screen will appear. The Mediaguide will now remain on permanently.

Take a lanyard, clip the carabiner into the loop on the casing and plug the audio jack into the designated socket. The device is now ready for use.

 

Equipment return and top-up

Remove the headphones (and the lanyard). Insert the device into the charging station with the loop facing forwards and upwards. As you do so, lift the rear end of the device slightly and push it in until you feel resistance. Lower the device and let it click gently into the socket. Only once you can feel that the device has been inserted into the socket should you push it further until it stops. After a few seconds, the display will switch to the charging screen, showing the battery charge level.

Note: If the display does not switch to the charging screen even though the device is correctly plugged in, please check that the charging station is switched on and connected to the mains. If necessary, try plugging the device into a different socket. If none of this helps, the device may need to be restarted (see ‘Restart’).

 

Switching off devices

If you remove a device from the charger and leave it in the xpedeoscreen, the screen will switch off automatically after one minute. You can leave it there for several hours without charging it. To switch it back on, press briefly on the side of the casing (see ‘Restart’).

To switch off a device for a longer period or permanently, follow the same procedure as for ‘Restart’ and this time tap ‘Switch off’. The device will shut down and switch off completely. To switch it back on, you must press and hold the side of the casing again.

When switching on, a prompt will appear asking whether the volume should be increased beyond the recommended level. Tap ‘OK’ to allow the volume to be raised above the safe level. Otherwise, the audio will be too quiet.

 

Restarting the software / a device

If something isn’t working, it may help to restart the Xpedeo software. To do this, go to the administration area and click the ‘Restart’ button at the very bottom.

If that doesn’t help either, restart the device. To do this, open the administration area. On the Guide, press and hold the side of the upper half of the casing (see illustration) until the options ‘Restart’, ‘Shut down’ etc. appear. Tap the ‘Restart’ option and confirm your selection if prompted. Wait until the Xpedeo application has restarted.

Note: If pressing the casing simply turns off the display without showing the options, you have pressed it for too short a time; press the casing briefly again to switch the display back on, then press and hold it once more. If a device cannot be restarted using either of these methods, please contact us (support@xpedeo.de).

 

Messages following a device restart

If an xpedeo device needs to be restarted, you may be prompted to respond to a few system queries.

Warning regarding volume

A message will appear asking whether the volume should be increased beyond the recommended level. Please tap ‘OK’. The volume is controlled via the xpedeo software. 

Prompt for a system update

The device may attempt to carry out a system update after a restart. You should prevent this at all costs, as there is no guarantee that the xpedeo software will still run and function correctly afterwards. If the ‘System update available’ dialogue box appears, simply close the window. There are three buttons below the update window. Tap the right-hand button (square) and then tap the small X in the top right-hand corner of the (minimised) update window. Alternatively, you can swipe the window to the right or tap ‘Close All’.

 

Administration area

The handouts you received with your loaned equipment explain how to access the administration area.

Updating content

Click on the ‘Update’ button. The device will connect to the server and compare its files with the list provided by the server. Only out-of-date or missing files will be downloaded.

Updating the app

Along with the content, a new software version (APK file) will be downloaded if required. Depending on your system’s configuration, the new software version will then be installed automatically.
Alternatively, you’ll need to tap the ‘Software Update’ button, which is now active.

 

 

Guidance and possible solutions

The display is black; the device is not responding

  • Connect the device to a charger. The battery charge indicator should now appear.
  • Press the side of the casing briefly (see ‘Restart’).
  • If the battery is completely flat, charge the device for about half an hour.
    Then press and hold the side of the device (see ‘Restart’).

The device does not respond when connected to the mains

  • Is the charging station connected to the mains or, if applicable, is a timer switch active?
  • Try a different slot on the charging station.
  • If the battery is completely flat, it may take several minutes for the device to display anything on the screen.